Add files via upload

Marlin/Configuration.h

@@ -1,5 +1,5 @@
 /**
- * Marlin 3D Printer Firmware
+ * 5000arlin 3D Printer Firmware
  * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
@@ -950,8 +950,9 @@
     #define MAX_JERK_EDIT_VALUES {20, 20, 0.6, 10 } // ...or, set your own edit limits
   #endif
 #endif
+
 #if ENABLED(HIGH_SPEED_1)
-#define DEFAULT_EJERK 10.0  // May be used by Linear Advance
+#define DEFAULT_EJERK 5.0  // May be used by Linear Advance
 #else
 #define DEFAULT_EJERK 5.0  // May be used by Linear Advance
 #endif
@@ -976,7 +977,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-#define S_CURVE_ACCELERATION
+//#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -1153,6 +1154,7 @@
 #else 
  #define NOZZLE_TO_PROBE_OFFSET { -31.75, -14.69, 0}  //prime 2023.02.10 朱工提供
 #endif
+
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
 #define PROBING_MARGIN 3 
@@ -1414,7 +1416,7 @@
 
   #define FIL_RUNOUT_STATE     HIGH       // Pin state indicating that filament is NOT present.
   #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN           // (V3SE default) Use internal pulldown for filament runout pins.
   //#define WATCH_ALL_RUNOUT_SENSORS      // Execute runout script on any triggering sensor, not only for the active extruder.
                                           // This is automatically enabled for MIXING_EXTRUDERs.
 
@@ -1455,7 +1457,7 @@
   // With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
   // NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
   #define FILAMENT_RUNOUT_SCRIPT "M600"
-
+  //#define FILAMENT_RUNOUT_SCRIPT "M412 H"
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.

Marlin/Configuration_adv.h

@@ -1924,10 +1924,10 @@
  *
  * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  */
-// #define LIN_ADVANCE
+#define LIN_ADVANCE
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.2 //0.06    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.0 //0.2 //0.06    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
   #define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif
@@ -2438,10 +2438,10 @@
   #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
   //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif